Darach
"Darach" (Celtic Oak) Fine Handmade Custom Dagger
- Size: Knife: Length overall: 10.0" (25.4 cm), Blade Length: 5.5" (14 cm), Thickness: 0.132" (3.4 mm)
- Weight: Knife: 10.8 oz. (306 grams), Sheath: 6.0 oz. (170 grams)
- Blade: 440C High Chromium Martensitic Stainless Steel, Cryogenically Treated, Hardened and Triple Tempered to Rockwell HRC 59.5, Mirror Polished, Hand-engraved
- Bolsters, Fittings: Hand cast bronze, Hand-engraved
- Handle: Nephrite Jade Gemstone (Wyoming)
- Sheath: Hand-carved, Hand-dyed Leather Shoulder
- Knife Blade: This is a new design, and a great
custom knife that was an honor to make. My client requested a Celtic
leaf bladed dagger, so I named this one Darach. Darach (or daraich)
is the Scottish Gaelic word for oak. I created the entire theme of
the knife based around the inspiration, the mighty oak, which is a
symbol of life, strength, and wisdom. The blade is a leaf-bladed
dagger, a difficult and challenging blade to make. I ground the
blade, finished it to pre-polish, and then hardened and tempered the
steel. This was not a simple process, the pinnacle of
treatment for this steel takes 15 steps and 95 hours. In it, the
steel is brought to cryogenic temperatures and aged for over 60
hours, followed by triple tempering and deep cryogenic soaks at -325°F
for thermal cycling, full conversion of allotropes, and the greatest
condition. This makes the steel very hard and wear resistant, very
tough, and extremely corrosion resistant. I ground the blade with a
1.5" radius wheel hollow grind, for a thin, sharp cutting edge and a
full, wide blade flat for the artwork. The challenge here is that I
hand-engraved the knife blade flats before heat treatment, since it
would be impossible to engrave it after it's hardened. I could only
finish the steel by removing less than a half a thousandth of an
inch of material to bring it to a polish without losing any of the
engraving. In the photos, you can see the gentle color gradient in
the engraved lines of straw, blue-gray, and dark gray from the heat
treating process. It's like a rainbow effect in just the right
light. I chose a triquetra-based pattern design for the motif; it
has bold and thick forms that worked well with the wide, leaf-shaped
blade, filling it with visual interest and commanding structure. The
forms are intertwined, knotted and complex (like life), and are
extended to
five-cornered designs at the ricasso and blade termination toward
the guard, appropriate to the Celtic design and pattern arrangement
of the artwork.
- Fittings: The guard and pommel had to be
appropriate and matching to the work, and my client requested an
acorn pommel, so I hand-cast the fittings in bronze. This is done by
painstakingly designing and carving the models in wax, investing the
wax in a mold, burning out the wax and hardening and curing the
mold, and casting the mold in molten bronze at over 1800°F.
After casting, the bronze is de-sprued, fettled (cleaned and carved
back to its original form) and machined, milled, hand-ground,
hand-finished, and engraved. The process takes many days. I chose a full guard with rounded
finials to accommodate the engraved design of triquetras and
interwoven knotwork. The pommel is an acorn of solid bronze, drilled
and threaded to bond the pommel to the tang and secure the handle.
The bronze will age to a rich golden hue, bringing out the straw
colors in the blade engraving.
- Handle: I wanted a truly special handle, an my
client requested a wire-wrapped design. I made the handle in solid
nephrite jade gemstone from Wyoming, an extremely tough and
beautiful deep green jade. I carved and polished the jade in a
spiral domed form, reflecting the twisted vines of living things,
wrapped in sterling silver twist to match. I finished the jade it to a bright vitreous finish,
rich and complete. The carved jade is
not only beautiful but also feels wonderful; it's tough and hard and will
literally outlast the rest of the knife, and the rest of us, for
generations! The deep green accentuates the focus of dynamic oak and
life dominating the design and artwork.
- Sheath: The sheath had to be special, and
commensurate and dedicated to the knife, form, and artwork. I
created the sheath in 9-10 oz. leather shoulder, and hand-carved and
hand-dyed a special design of Celtic knotwork matching the knife
engraving and pattern. The artwork is bold and strong, working with
the color of the knife handle, and is appropriate in the front,
back, and even in the belt loop of the sheath. The sheath is
meticulously hand-dyed for just the right appearance, and stitched
with black polyester for durability. Even the retainer strap is
embellished with artwork and has a brass snap matching the bronze of
the knife guard and pommel. The entire sheath is sealed with lacquer
for longevity and easy care.
- This is a beautiful, unique, and original piece of artwork, and
was a great pleasure and honor to create for my client!
Thanks, M. H.!
Oh my God! It is beautiful! I love it!!!!!!!!!!!!!!!!!!!!!!!
It is PERFECT. I could not have asked for a better representation. Even the name! Perfect. I cannot wait to hold her.
I cannot wait to see it in real life. I am nearly giddy!
-and-
It is here! And it is beautiful! Thank you!
--M.
Please click on thumbnail knife photos